A yellow container in a workshop with its whole side panel lifted on struts, like an awning

Project case · Equipment enclosure · Full side opening

A Container Whose Whole Side Lifts

One panel the length of the long side, hinged at the top and held open on two struts. Open, it is an awning over the working area. Closed, it is a wall with a man door in it.

1side panel, full length
2struts holding it open
0partitions inside
1man door in the panel
ClientEquipment supplier (not named)
LocationChina, workshop and yard photographs
ScopeYellow container with a top-hinged side panel the full length of the long side, two support struts, man door set into the panel, painted floor
ContractShell, side panel and hinge fabrication, strut mounting, paint
SiteFabrication shop; photographed open in the shop and closed on a lowbed
01 / The brief

Opening the side is a loading decision

It is about what goes in, and how

Anything that arrives on a skid, a pallet or a frame and is too tall for a door gets loaded through the side. With the panel up, the crane or the forklift has the full length of the box to work with and the roof stays where it is.

Hinged at the top rather than the bottom, so the panel does not become a ramp, a trip hazard or a place where water sits.

The struts carry the weight, not the crew

Two struts hold the panel at working height. The panel is sheet steel with a frame, and it is heavy: nobody holds it while somebody else finds a prop.

Sealing is the part that gets skipped on this kind of opening. The gasket runs the full perimeter, the top hinge is covered by a drip, and the panel is pulled down onto the seal by the latches, not by gravity alone.

02 / What we delivered

Three details

Closed, it is a wall
01 / PanelClosed, it is a wall

The man door is cut into the side panel itself, so the panel is also the access. Latches along the bottom edge pull the whole length down onto the gasket.

Hinged at the top
02 / HingeHinged at the top

The hinge line is above the opening, under a drip. Water runs off the panel and past the seal instead of standing on it.

Closed for the road
03 / TransportClosed for the road

Latched, strapped and sitting on a lowbed. The panel travels closed: an open side is not something to move on a public road.

03 / Sequence

How it went together

Step 1Clear openingSide opening set to the widest item that has to go through it.
Step 2FrameOpening framed out and the hinge line built above it, with a drip.
Step 3PanelPanel framed, skinned, man door cut in, gasket run round the edge.
Step 4StrutsStrut mounts welded to the frame and the panel, tested through full travel.
Step 5Load outClosed, latched, water-tested, then lifted onto the lowbed.
04 / By the numbers

The opening, in four numbers

1panel, full length of the side
2struts holding it at working height
1man door, set into the panel
0partitions inside

Counted from the shell. Commercial values are not disclosed.

05 / Site record

Open in the shop, closed on the trailer

Closed: the side panel is the wall, man door included
Closed: the side panel is the wall, man door included
The hinge line and the strut pick-up at the top rail
The hinge line and the strut pick-up at the top rail
Latched down and strapped for the road
Latched down and strapped for the road
Figures & disclosure

Photographs are from the delivered project. The client is not named and the site is not disclosed. Commercial values are withheld; the figures describe the build as shipped.

Tell us the biggest thing that has to go in.

Height, width and how it is lifted decide the opening; the opening decides the frame. Send those three and the rest follows.

Talk to an engineer

Contact us

Committed to providing customers with high-quality and reliable container solutions.

ACTBOXES Whatsapp